Matte Varnish 16 oz.
* Low viscosity - very fluid.
* Produces a matte finish
* Does not drastically reduce color depth as does Matte Medium.
* 100% acrylic polymer varnish. Water soluble when wet. Good chemical and water resistance when dry.
* Dry to a non-tacky, hard, flexible surface that is resistant to retention of dirt.
* Resist discoloring (non-yellowing, non-fogging) due to humidity, heat and ultraviolet light.
* Depending upon substrate, allows moisture to pass through (breathable).
* Will not crack as surface expands and contracts during temperature and humidity changes. Applicable for any acrylic painted surface (flexible and rigid) on canvas, paper, wood, stone, Plexiglas, etc.
* Not for use over oil paint.
* Flexible, archival, non-yellowing and water resistant when dry.
* For interior use only
* Apply as a final varnish over dry acrylic paint.
* Varnish surface and environment must be clean, dry and dust free.
* Acrylic paintings must be completely dried and cured for a minimum 48-72 hours before varnishing.
* Application may be done by brush or spray. Generally a sprayed application will be thinner, smoother and more even. Rolling or sponging application is not recommended.
* If more than 1 varnish coat is desired, apply 1-2 coats of Liquitex Gloss Varnish before applying a final coat of Liquitex Matte Varnish.
* Caution: Acrylic paints and mediums become increasingly brittle in cold weather. Do not apply below 60 degrees.
Brush and Paint Pad Application
1. Use a wide, soft hair brush or paint pad (vacuum pad prior to use to remove lint). Size of area to be varnished will determine the size of the applicator. The smaller the surface area, the narrower the brush. Generally, a 1-4" flat brush is used.
2. Apply varnish in 1-3 thin coats, rather than 1 thick coat. A thick coat will take longer to dry, may dry cloudy, may drip or sag during application and has a greater chance of showing brush strokes when dry.
3. Horizontal surface application is best with less chance of varnish running. After varnishing, the surface should be shielded with a protective "tent". This will prevent any dust or airborne particles from settling into varnish as it dries.
4. Apply varnish in slightly overlapping pattern that covers entire artwork. Apply in horizontal and vertical brush strokes, so that entire area is evenly coated.
5. Do not rework areas you might miss, as the brush could pick up partially dried varnish and cause clouding. If areas are missed, wait until the varnish is dry and apply another coat.
6. When applying Liquitex Matte Varnish or Satin Varnish, apply no more than 1-2 thin coats. A thick application may result in cloudiness when dry. If more than 2 coats are desired, first varnish with Gloss Varnish until desired thickness is achieved, then final varnish with matte or satin varnish.
Refer to Techniques and search on Airbrushing for more detailed information.
* Most even application method.
* Use for textured surfaces (thick impasto, thick textures), where brush application may result in foaming and fragile surfaces (watercolor, tempera, graphite, pastel, gouache), where brush application may disrupt drawing or painted surface.
1. Select air pressure (PSI) depending on air gun used and viscosity of varnish. Greater PSI permits thicker varnish to be sprayed, but may affect fragile surfaces.
2. 2-3 light even coats are better than 1 thick coat.
3. Spray a continuous film by moving the spray gun in a smooth motion from one side of the painting to the other. First coat horizontal, second coat, third coat horizontal, etc.
4. During spray application maintain same distance across the surface of the artwork. Move your body as well as your arm to avoid "arching" motion and uneven application.
* Thinning increases penetration and can make it easier to apply varnish.
* Over thinning may result in weak varnish film, poor adhesion, running and soaking into substrate.
* Thin, if desired, with a small amount of water to allow the varnish to flow easily from the brush or airbrush.
* Thin with small amount of Flow-AidTM/water to reduce brush marks or spray apply. Refer to Liquitex Paint Additives: Flow-AidTM Flow Enhancer.
* Not removable. Do not attempt to remove these varnishes with harsh solvents.